diff options
Diffstat (limited to '')
| -rw-r--r-- | doc/mpdconf.example | 344 |
1 files changed, 173 insertions, 171 deletions
diff --git a/doc/mpdconf.example b/doc/mpdconf.example index 8f77a4ace..8fe6353b6 100644 --- a/doc/mpdconf.example +++ b/doc/mpdconf.example @@ -1,243 +1,245 @@ -# MPD CONFIG FILE -# For a full description of all config parameters, -# Check the mpd man page, "man mpd". - -##################### REQUIRED ########################### -music_directory "~/music" -playlist_directory "~/music" -db_file "~/.mpd/mpd.db" -log_file "~/.mpd/mpd.log" -error_file "~/.mpd/mpd.error" -pid_file "~/.mpd/mpd.pid" -########################################################## - -########################################################## -# EVERYTHING ELSE IS OPTIONAL -########################################################## - -################## AUDIO OUTPUT ########################## -# -# use this if you want to use OSS audio output -#audio_output { -# type "oss" -# name "my OSS sound card" -# device "/dev/dsp" # optional -# format "44100:16:2" #optional -#} -# -# use this if you want to use ALSA audio output -#audio_output { -# type "alsa" -# name "my ALSA device" -# device "hw:0,0" # optional -# format "44100:16:2" #optional -#} +# An example configuration file for MPD +# See the mpd.conf man page for a more detailed description of each paramaeter. + +######################## REQUIRED PATHS ######################## +music_directory "~/music" +playlist_directory "~/.mpd/playlists" +db_file "~/.mpd/mpd.db" +log_file "~/.mpd/mpd.log" +error_file "~/.mpd/mpd.error" +################################################################ + + +######################## OPTIONAL PATHS ######################## # -# as a last resort, try using libao -#audio_output { -# type "ao" -# name "default ao output" -#} +# If you wish to use mpd --kill to stop MPD, then you must +# specify a file here in which to store MPD's process ID. # +#pid_file "~/.mpd/mpd.pid" # -# Set this if you have problems -# playing audio files. -# This will resample your music so -# that it comes out at the set rate. +# If specified, MPD will save its current state (playlist, +# current song, playing/paused, etc.) at exit. This will be +# used to restore the session the next time it is run. # -#audio_output_format "44100:16:2" +#state_file "~/.mpd/mpdstate" # -########################################################## +################################################################ -################### VOLUME MIXER ######################### +######################## DAEMON OPTIONS ######################## +# +# If started as root, MPD will drop root privileges and run as +# this user instead. Otherwise, MPD will run as the user it was +# started by. If left unspecified, MPD will not drop root +# privileges at all (not recommended). # -# Examples: -# ALSA Mixer -#mixer_type "alsa" -#mixer_device "default" -#mixer_control "PCM" +#user "nobody" # -# OSS Mixer -#mixer_type "oss" -#mixer_device "/dev/mixer" -#mixer_control "PCM" +# The address and port to listen on. # -# Software Mixer -#mixer_type "software" +#bind_to_address "any" +#port "6600" # -########################################################## +# Controls the amount of information that is logged. Can be +# "default", "secure", or "verbose". +# +#log_level "default" +# +################################################################ -################# SHOUT STREAMING ######################## +########################## PERMISSIONS ######################### # -# Set this to allow mpd to stream its output to icecast2 -# (i.e. mpd is a icecast2 source) +# MPD can require that users specify a password before using it. +# You may specify one ore more here, along with what users who +# log in with that password are allowed to do. # -#audio_output { -# type "shout" -# name "my cool stream" -# host "hostname" -# port "8000" -# mount "/mpd.ogg" -# password "hackme" -# quality "5.0" -# bitrate "128" -# format "44100:16:1" +#password "password@read,add,control,admin" +# +# Specifies what permissions a user who has not logged in with a +# password has. By default, all users have full access to MPD +# if no password is specified above, or no access if one or +# more passwords are specified. # -# Optional Parameters -# user "source" -# description "here's my long description" -# genre "jazz" -#} # end of audio_output +#default_permissions "read,add,control,admin" # -########################################################## +################################################################ -################# FILESYSTEM SETTINGS #################### +########################## AUDIO OUTPUT ######################## # -# If the names of files or directories are -# not correctly displayed then set the -# following to the filesystem coding. +# MPD supports many audio output types, as well as playing +# through multiple audio outputs at the same time. You can +# specify one or more here. If you don't specify any, MPD will +# automatically scan for a usable audio output. # -# Usually this is either: -# ISO-8859-1 or UTF-8 +# See <http://mpd.wikia.com/...> for examples of other audio +# outputs, such as PulseAudio, libao, etc. # -# After changing the filesystem_charset -# you will need to recreate the db: -# mpd --create-db +# An example of an ALSA output: # -#filesystem_charset "ISO-8859-1" +#audio_output { +# type "alsa" +# name "My ALSA Device" +# device "hw:0,0" # optional +# format "44100:16:2" # optional +#} # -########################################################## - - -#################### OPTIONAL FILES ###################### +# An example of an OSS output: +# +#audio_output { +# type "oss" +# name "My OSS Device" +# device "/dev/dsp" # optional +# format "44100:16:2" # optional +#} +# +# An example of a shout output (for streaming to Icecast): +# +#audio_output { +# type "shout" +# name "My Shout Stream" +# host "localhost" +# port "8000" +# mount "/mpd.ogg" +# password "hackme" +# quality "5.0" +# bitrate "128" +# format "44100:16:1" +# user "source" # optional +# description "My Stream Description" # optional +# genre "jazz" # optional +# public "no" # optional +#} # -# The state file (if set) will be a file -# for storing all current information -# (playlist, playing/paused, etc...) from -# the last MPD session. This will be used -# to recreate your last MPD session after -# restart. +# Force all decoded audio to be converted to this format before +# being passed to the audio outputs. # -#state_file "~/.mpd/mpdstate" +#audio_output_format "44100:16:2" # -########################################################## +################################################################ -################# Normalization ########################## +############################# MIXER ############################ # -# Use Replay Gain (album or track) -# http://www.replaygain.org +# MPD needs to know what mixer settings to change when you +# adjust the volume. If you don't specify one here, MPD will +# pick one based on which ones it was compile with support for. # -#replaygain "album" +# An example for controlling an ALSA mixer: # -# Sets the pre-amp used for files that have replaygain -# info. Valid values are between -15 to 15 (in dB). +#mixer_type "alsa" +#mixer_device "default" +#mixer_control "PCM" # -#replaygain_preamp "0" +# An example for controlling an OSS mixer: # -# Normalization increases the amplitude of the audio -# waveform to the maximum level without introducing any -# distortion into the recording. This option will -# normalize when replaygain is not on, utilizing the -# CPU for calculation. +#mixer_type "oss" +#mixer_device "/dev/mixer" +#mixer_control "PCM" # -#volume_normalization "yes" -########################################################## +# If you want MPD to adjust the volume of audio sent to the +# audio outputs, you can tell it to use the software mixer: +# +#mixer_type "software" +# +################################################################ -################ OUTPUT BUFFER SETTINGS ################## +######################### NORMALIZATION ######################## # -# You should not need to mess with this -# unless you know what you're doing. +# Specifies the type of ReplayGain to use. Can be "album" or +# "track". ReplayGain will not be used if not specified. See +# <http://www.replaygain.org> for more details. # -#audio_buffer_size "2048" +#replaygain "album" # -# This means exactly what it says, it will -# buffer your file up to the percentage of -# the buffer before it begins playing. +# Sets the pre-amp used for files that have ReplayGain tags. # -#buffer_before_play "25%" +#replaygain_preamp "0" # -########################################################## - - -################### HTTP PROXY ########################### +# Enable on the fly volume normalization. This will cause the +# volume of all songs played to be adjusted so that they sound +# as though they are of equal loudness. # -# http_proxy_host "proxy.isp.com" -# http_proxy_port "8080" -# http_proxy_user "user" -# http_proxy_password "password" +#volume_normalization "no" # -########################################################## +################################################################ -################# SECURITY SETTINGS ###################### +########################### BUFFERING ########################## # -# It is encouraged to run MPD as -# non-superuser. If you start mpd as root -# (for example, in an init script), set -# this value, then mpd will drop root privileges -# and runs as the user specified. +# The size of the buffer containing decoded audio. You probably +# shouldn't change this. # -#user "nobody" +#audio_buffer_size "2048" # -# Set this value if you only have one -# address you want to allow connection to. +# How much of the buffer to fill before beginning to play. # -#bind_to_address "localhost" +#buffer_before_play "0%" # -# If you want to setup MPD to use -# passwords set them here +# Similar options for the HTTP stream buffer. If you hear +# skipping while playing HTTP streams, you may wish to increase +# these. # -#password "password1@read,add,control,admin" -#password "password2@read" +#http_buffer_size "128" +#http_prebuffer_size "25%" # -# Specify permissions used by default when no password is -# given by for a connection/client. -# -#default_permissions "read,add,control,admin" -# -########################################## +################################################################ -################ MISCELLANEOUS OPTIONS ################### +########################### HTTP PROXY ######################### # -#port "6600" +# Specifies the HTTP proxy to use for playing HTTP streams. # -# This determines what encoding ID3v1 tags should be converted from. +#http_proxy_host "proxy.isp.com" +#http_proxy_port "8080" +#http_proxy_user "user" +#http_proxy_password "password" # -#id3v1_encoding "ISO-8859-1" +################################################################ + + +############################# LIMITS ########################### # -# This sets the metadata mpd will use, to disable all metadata, set to "none" -# NOTE: comments are disabled by default +# These are various limits to prevent MPD from using too many +# resources. You should only change them if they start +# restricting your usage of MPD. # -#metadata_to_use "artist,album,title,genre,date,track,composer,performer,comment" +#connection_timeout "60" +#max_connections "5" +#max_playlist_length "16384" +#max_command_list_size "2048" +#max_output_buffer_size "8192" # -# This setting exists as precaution against attacks. +################################################################ + + +###################### CHARACTER ENCODINGS ##################### # -#max_playlist_length "16384" +# If file or directory names do not display correctly, then you +# may need to change this. In most cases it should be either +# "ISO-8859-1" or "UTF-8". You must recreate your database +# after changing this (use mpd --create-db). # -# Valid options are "default", "secure" or "verbose". -#log_level "default" +#filesystem_charset "ISO-8859-1" # -#connection_timeout "60" +# The encoding that ID3v1 tags should be converted from. # -# This should be fine for 2-3 people using clients -# at the same time. +#id3v1_encoding "ISO-8859-1" # -#max_connections "5" +################################################################ + + +######################### OTHER OPTIONS ######################## # -# No need to change these unless you know better. +# The metadata types MPD will recognize. # -#max_command_list_size "2048" -#max_output_buffer_size "8192" +#metadata_to_use "artist,album,title,track,name,genre,date,composer,performer,disc" # -# This will make playlists compatible with normal music -# players. +# Enable this if you wish to use your MPD created playlists in +# other music players. # #save_absolute_paths_in_playlists "no" # -########################################################## +################################################################ |